www.austriamicrosystems.com/AS5140H
Revision 1.4
19 - 37
AS5140H
Data Sheet - Detailed Description
7.6 Programming the AS5140H
Note: A detailed description of the austriamicrosystems low voltage polyfuse OTP programming method is given in Application Note AN514X-
10, which can be downloaded from the austriamicrosystems website. The OTP programming description in this datasheet is for general
information only.
After power-on, programming the AS5140H is enabled with the rising edge of CSn with Prog = high and CLK = low. The AS5140H programming
is a one-time-programming (OTP) method, based on polysilicon fuses. The advantage of this method is that a programming voltage of only 3.3V
is required for programming. The OTP consists of 52 bits, of which 21 bits are available for user programming. The remaining 31 bits contain
factory settings and a unique chip identifier (Chip-ID).
A single OTP cell can be programmed only once. Per default, the cell is 0 ; a programmed cell will contain a 1 . While it is not possible to reset
a programmed bit from 1 to 0 , multiple OTP writes are possible, as long as only unprogrammed 0 -bits are programmed to 1 . Independent
of the OTP programming, it is possible to overwrite the OTP register temporarily with an OTP write command at any time. This setting will be
cleared and overwritten with the hard programmed OTP settings at each power-up sequence or by a LOAD operation.
The OTP memory can be accessed in several ways:
Load Operation: The Load operation reads the OTP fuses and loads the contents into the OTP register. Note that the Load operation is
automatically executed after each power-on-reset.
Write Operation: The Write operation allows a temporary modification of the OTP register. It does not program the OTP. This operation can
be invoked multiple times, and will remain set while the chip is supplied with power and while the OTP register is not modified with another
Write or Load operation.
Read Operation: The Read operation reads the contents of the OTP register, for example to verify a Write command or to read the OTP
memory after a Load command.
Program Operation: The Program operation writes the contents of the OTP register permanently into the OTP ROM.
Analog Readback Operation: The Analog Readback operation allows a quantifiable verification of the programming. For each pro-
grammed or unprogrammed bit, there is a representative analog value (in essence, a resistor value) that is read to verify whether a bit has
been successfully programmed or not.
7.6.1 OTP Memory Assignment
Table 19. OTP Bit Assignment
Bit
Symbol
Function
mbit1
Factory Bit
51
Md0
Incremental Output Mode Selection
50
Md1
49
Div0
48
Div1
47
Index
46
Z0
10 bit Zero Position
:
:
37
Z9
36
CCW
Direction
35
RA0
Redundancy Address
:
:
31
RA4
30
FS 0
Factory Bit
:
FS 1
Factory Bit
18
FS 12
Factory Bit
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AS5145B-HSST-500
IC ENCODER ROTARY MAGN 16-SSOP
AS5510-DWLT
IC ENCODER MAGNETIC LIN 6-WLCSP
ATS137-PL-B-B
IC HALL SENSOR SGL 25MA SIP-3L
ATS177-PG-B-B
IC HALL SENSOR LATCH 25MA SIP-3L
ATS617LSGTN-T
IC HALL EFFECT GEAR SENSOR 4SIP
ATS625LSGTN-T
IC SENSOR GEAR TOOTH 4-SIP
ATS627LSGTN-T
IC HALL EFFECT GEAR SENSOR 4-SIP
ATS635LSETN-T
IC SENSOR GEAR TOOTH 4-SIP
相关代理商/技术参数
AS5140H-ASST-500
功能描述:板机接口霍耳效应/磁性传感器 RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23
AS5140HASSU
制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:10-Bit 360 Programmable Magnetic Rotary Encoder For High Ambient Temperatures
AS5140H-ASSU
功能描述:IC ENCODER PROG 10-BIT 16-SSOP RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
AS5140H-DB
制造商:ams 功能描述:AS5140H Demo Board
AS5140H-PB
制造商:ams 功能描述:AS5140H Progamming Board
AS5140-SS_EK_AB
功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:5V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5140 标准包装:1
AS5140-SS_EK_DB
功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5140 标准包装:1
AS51430FLF
制造商:TT Electronics / IRC 功能描述:AS51430FLF